Home > Knowledge > Content

The harm, cause and treatment of hydraulic shock in hydraulic system

Dec 07, 2023

In the hydraulic system, the liquid flowing in the pipeline often forms a high peak within the pipeline due to the rapid reversal and sudden closure of the valve port, which is called hydraulic shock.

First, the harm of hydraulic shock

1, the impact pressure may be as high as 3 to 4 times the normal working pressure, so that the components in the system, pipes, instruments, etc., are damaged.

2. The impact pressure caused by the impact makes the pressure relay send a false signal, interferes with the normal operation of the hydraulic system, and affects the working stability and reliability of the hydraulic system.

3, cause vibration and noise, loose connectors, resulting in oil leakage, pressure valve regulating pressure change, flow valve regulating flow change; The system is affected.

Second, the cause of hydraulic shock

1. Hydraulic shock occurs when the valve port in the pipeline is quickly closed.

2, the moving parts are suddenly stopped by the brake during high-speed movement, resulting in pressure impact (inertial impact).

For example, the cylinder piston suddenly stops or reverses in the middle of the stroke, the main reversing valve reverses too quickly, and the piston stops or reverses at the cylinder end, which will produce pressure shock.

The harm, cause and treatment of hydraulic shock in hydraulic system
Hydraulic valve group

Third, the general method to prevent hydraulic shock

The pressure shock caused by sudden closure of the valve port can be eliminated or reduced by the following methods.

1, slow down the closing speed of the reversing valve, that is, increase the reversing time. For example, the hydraulic impact of DC solenoid valve is smaller than that of AC solenoid valve; With a damped electro-hydraulic directional valve, the reversing (closing) speed of the main directional valve spool can be slowed by adjusting the damping and controlling the pressure and flow through the pilot valve, and the hydraulic directional valve is similar.

2, increase the diameter of the pipe, reduce the flow rate, to reduce the impact pressure, shorten the length of the pipe, avoid unnecessary bending; Using hoses also works.

3, slow down the flow rate of liquid before the slide valve is completely closed. For example, improve the structure of the control side of the reversing valve, that is, open a rectangular V-shaped straight slot on the edge of the valve core, or make a conical (half cone Angle 2° ~ 5°) throttle cone, compared with the right Angle control side, the hydraulic impact is greatly reduced; On the external grinding machine, the pilot reversing valve is prefabricated, and then the main reversing valve quickly jumps to the middle position, and the left and right cavities of the working table cylinder are instantaneously injected with pressure oil (the main valve is P-type), so that the working table can be balanced without impact; The reversing valve of the surface grinding machine table can be H-type, so that when the reversing valve is in the middle position after a quick jump, the left and right cavities of the cylinder are intercommunicated and the oil pool is passed, which can reduce the impact pressure during braking.

4, the moving parts are suddenly braking, decelerating or stopping, the resulting hydraulic shock prevention method (such as the cylinder).

① The speed reduction valve is used at the end of the stroke of the hydraulic cylinder, which eases the hydraulic shock by slowly closing the oil circuit.

② A small safety valve with fast response and high sensitivity can be set at the inlet and outlet of the cylinder (direct-acting type), and its adjusted pressure is 105% to 115% of the highest working pressure in the medium and low pressure system. Such as hydraulic planer, guideway grinding machine used in the system; In high pressure systems, 125% of the maximum working pressure, such as the system used by hydraulic presses. This allows the shock pressure not to exceed the above adjustment value.

③ Rubber hoses are used to absorb hydraulic shock energy.

(4) Set the stroke throttle valve in the fast forward to the working advance (such as the combined machine tool), and set the stroke bump block with two angles, through the reasonable design of the Angle, to prevent the pressure impact caused by the speed change too fast when the fast conversion to the working advance; Or use a two-speed conversion so that the speed conversion is not too fast.

⑤ A buffer device (such as a one-way throttle valve) is set at the end of the cylinder to control the oil discharge speed of the end of the cylinder, so that the cylinder movement stops at the end of the cylinder, stable and no impact.

⑥ The accumulator is set at the position of the pipe path that is easy to produce hydraulic shock to absorb the impact pressure.

7 Set the balance valve (vertical hydraulic press) and back pressure valve (horizontal hydraulic press) in the cylinder oil return control oil circuit to control the forward impact of rapid decline or movement, and appropriately adjust the back pressure pressure.

⑧ The hydraulic direction change valve with damping is used, and the damping is increased, that is, the one-way throttle valve at both ends is turned off, and the main direction change valve (hydraulic) in the general grinding machine control box is set with this structure.

⑨ When the clearance of the cylinder block hole is too large, or the seal is damaged, and the working pressure is adjusted to a large extent, it is easy to have impact. You can rematch the piston or replace the piston seal, and appropriately reduce the working pressure to eliminate the impact caused by it.

 

Send Inquiry