Home > Knowledge > Content

The types and characteristics of the adjusting mode of the hydraulic motor at the output end of the hydrostatic drive device

Mar 26, 2024

1. Determination of pump and motor displacement
Whether it is a closed system or an open system, whether it is a quantitative motor or a variable motor, the choice of motor displacement is usually set according to the maximum load torque when balancing the work, or the starting torque requirements when the working condition is harsh.
Whether it is a closed system or an open system, whether it is a quantitative pump or a variable pump, the maximum displacement of the pump is determined according to the rated speed of the engine and the maximum speed of the motor displacement.


2. Why use variable motor
Although the closed system uses a quantitative motor with small size, low cost and high efficiency as much as possible, it is determined by the nature of the hydraulic system, and sometimes the output speed obtained by adjusting the input end (engine + variable pump) is limited by factors such as efficiency and cost. Therefore, on some devices, we need to consider the output side to adjust at the same time. The output torque of the general system is sufficient, and the output adjustment is more to expand the output speed range of the high efficiency zone.


3. What are the adjustment methods of the output end and their characteristics
The adjustment methods of the output end mainly include changing the motor displacement, changing the transmission ratio of the rear mechanical transmission, increasing or decreasing the number of online motors. The following are elaborated.
The hydrostatic drive device is mainly matched with the diesel engine, the diesel engine can be used with a speed ratio of about 2 to 4 (such as the speed from 800-3000), and the rated power near the working point is only 1.15 to 1.3. Therefore, the available pitch ratio of the engine is the main factor affecting the speed coverage of the travelling machinery.
Variable pump + quantitative motor way, variable pump displacement from about 25% to 100% change, and engine matching, the total speed ratio is about 8~16, the total pitch ratio is about 4~6. This way is more suitable for walking speed is small (such as less than 25km/h, 25/16=1.56km/h=0.43m/s, basically can achieve low speed walking), traction torque change is not very large (such as traction torque change is less than 5 to 10 times), walking power is small equipment, Such as hard forklift, slip steering loader, vibration roller and so on.
1) Variable pump + variable motor
The displacement of the dependent variable motor changes between about 40% and 100%, so the total speed change ratio is about 20 to 40, and the total pitch change ratio is about 10 to 15. The maximum driving speed can cover about 40Km/h (40/40=1Km/h=0.28m/s, basically can achieve low speed walking) equipment.

 

The advantages are as follows:
1.1) The high efficiency zone of the hydrostatic device is expanded
When the commonly used operating speed and empty transport speed of the large difference in equipment, if the use of large displacement quantitative motor (load determination), high-speed light load required flow is relatively large, the displacement of the pump needs to be larger, but at this time the system pressure is relatively low, so the pipeline pressure loss ratio is higher, the system efficiency deteriorates when working. When the low speed and high torque, the displacement of the pump needs to be reduced, and the volumetric efficiency is also not high. Therefore, variable motor can be selected to solve the above contradictory problems. At this time, the maximum displacement of the motor can be determined according to the maximum load in the low-speed high-torque load, and the displacement of the pump can be determined according to the high-speed light-load, when the motor is a small displacement. The maximum displacement of the motor is unchanged, but the maximum displacement of the pump is reduced, and the reduction ratio is equivalent to the displacement ratio of the motor. After the variable motor is used, the output envelope of the hydrostatic drive device is expanded to the high-speed area (as shown below), and the high efficiency area of the hydrostatic device is expanded. Although the variable motor is used, the variable motor works at a small displacement, the motor efficiency is reduced, and the variable motor cost is also higher. However, the advantages of variable motor outweigh the disadvantages. Therefore, it is more suitable for large power, large torque changes, and large speed changes.
The types and characteristics of the adjusting mode of the hydraulic motor at the output end of the hydrostatic drive device
The types and characteristics of the adjusting mode of the hydraulic motor at the output end of the hydrostatic drive device
The types and characteristics of the adjusting mode of the hydraulic motor at the output end of the hydrostatic drive device
1.2) Relax the maximum output speed limit, and the speed of many variable motors with small displacement is significantly higher than the allowable speed of large displacement, which can increase by about 20%, and this speed is what we need.
The types and characteristics of the adjusting mode of the hydraulic motor at the output end of the hydrostatic drive device

1.3) Zero displacement motor features, some new plunger motors can adjust the displacement to zero in operation, with this motor can make the drive wheel in the condition of not stopping between the drive and free wheel conditions to switch.
1.4) Improve the cost performance. When the large-displacement quantitative motor is matched with a large-size variable pump and a large-diameter high-pressure hose, it exceeds the scope of economic scale production (for example, when the displacement of the pump is greater than 160ml/r, and the diameter of the pressure-resistant 400bar hose is greater than 25mm), the price of the components will increase greatly.
2) Variable pump + quantitative motor + transmission
Because the variable motor is low in efficiency, large in size and expensive in price, sometimes it is better to use the high-speed quantitative motor + rear transmission, rather than the variable motor, which is especially suitable for the whole machine with a wide difference in operation and idle transfer speed. The disadvantage is that if there is no clutch, you need to stop or change gear when the speed is very low.
3) Variable pump + variable motor + transmission
If the driving speed is higher, such as greater than 40Km/h. When driving at high speed and light load, the motor displacement is 25% and the system pressure is 100bar. When driving at low speed, if the load torque is increased by 20 times and the motor displacement is 100%, the system pressure may reach 500bar, so it is necessary to consider increasing the motor displacement to meet the maximum load torque demand. However, at high speed, even if the motor works at a small displacement to achieve the necessary travel speed, a larger flow rate is required, so a larger displacement pump and a larger diameter pipeline are required, increasing the cost. Therefore, the rear-mounted gearbox can be added to expand the total equivalent displacement adjustment range through the mechanical transmission ratio. It is suitable for vehicles with large propulsion requirements and a wide speed range (such as vehicles with a speed of more than 40~50km/h), and it is necessary to add equipment such as transmission at the output end.
The types and characteristics of the adjusting mode of the hydraulic motor at the output end of the hydrostatic drive device
4) Multi-hydraulic motor switching system
The use of multiple small displacement motors instead of a larger displacement motor to improve the pitch ratio and speed ratio, mostly for the following reasons.
4.1) The required output torque is relatively large, the use of a single hydraulic motor can not meet the requirements or uneconomic;
4.2) The required speed is high, and the allowable speed of the large displacement motor cannot be reached or is not economical;
4.3) Matching installation space requirements.
The applications are as follows:
4.1) Zero displacement motor in high speed scheme
The number of working motors is changed in a low energy consumption control mode, which significantly improves the variable pitch ratio and variable speed ratio of the multi-motor system, and can be switched between travels. For example, Ma Da has a displacement of 120L/r, a displacement ratio of 1:4, and a minimum displacement of 30ml/r. If a 15ml/r quantitative motor +105ml/r displacement large motor is used, the variable displacement ratio is 8:1, and the efficiency of the 15ml/r quantitative motor is much higher than the efficiency of the variable motor working in the small displacement. Travel speed up to 40-50km/h. For high-power machinery, high-speed solutions often need to use a combination of multi-motor switching and rear-mounted transmission shift. A manual transmission without a clutch requires a stop or low speed to shift gears. With the clutch, it can change gear between trips.
The types and characteristics of the adjusting mode of the hydraulic motor at the output end of the hydrostatic drive device
The types and characteristics of the adjusting mode of the hydraulic motor at the output end of the hydrostatic drive device
4.2) Free wheel motor in low speed scheme
Wheel motors are used in low speed schemes. Wheel motors are generally internal curve motors with free wheel functions, but they cannot be integrated with a rear gearbox, and the total equivalent displacement can only be changed by switching the number of online motors. For example, four-wheel drive switches to two-wheel drive to achieve a doubling of speed and torque. The zero-displacement motor in the high-speed solution above can be switched between trips without impact. However, the curve motor in the wheel can only achieve the free wheel function in the parking or very low speed conditions.
In the low speed scheme, the zero-displacement motor + wheel reducer is equivalent to the wheel motor, and the number of online motors can be changed while traveling. However, due to the action of the reducer, the drag resistance is larger.
It should be noted that when the motor is in the free wheel or zero displacement state, the motor loses the braking ability.
4.3) Differential displacement motor regulation)
The maximum allowable speed of the motor has always been an important factor limiting the increase of vehicle speed. In particular, the influence of the wheel motor in the low speed scheme is more significant, the maximum allowable speed of the wheel motor in normal operation changes with the displacement, but the maximum speed is about 200-400r/min, while the free wheel speed can reach 1000-1200r/min, so you can consider using different displacement motors to drive different driving wheels. Different driving speeds are obtained by matching different displacement motors and switching the number of online motors. When the high speed light load, the small displacement motor works, the large displacement motor is adjusted to the free wheel state or zero displacement state to improve the driving speed. When heavy and low speed, four motors work simultaneously to ensure adequate traction. More suitable for low speed heavy load and high speed light load equipment.

 

Send Inquiry