Hydraulic cylinder is an executive element that converts hydraulic energy into mechanical energy in hydraulic system. The fault can be basically summarized as hydraulic cylinder misoperation, inability to push the load and piston slip or crawl. Due to the failure of the hydraulic cylinder, the phenomenon of equipment shutdown is not uncommon, so we should pay attention to the fault diagnosis and use of the hydraulic cylinder.
1. Misaction or action failure
There are several reasons and ways to deal with them:
(1) The spool is stuck or the valve hole is blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check valve body for wear.
(2) The piston rod and cylinder are stuck or the hydraulic cylinder is blocked. At this time, no matter how to operate, the hydraulic cylinder does not move or moves very little. At this time, it should be checked whether the piston and piston rod seal is too tight, whether it enters the dirt and colloid precipitate: whether the shaft line of the piston rod and the cylinder is in alignment, and whether the wearing parts and seals are invalid.
(3) The hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.
(4) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.
(5) The initial action of the hydraulic cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor fluidity, resulting in slow hydraulic cylinder action. The improvement method is to replace the hydraulic oil with good viscosity and temperature performance, and the oil temperature can be increased at low temperature by heating the heater or heating the machine itself.
2. Can not drive the load when working
The main performance is that the piston rod is not allowed to stop, the thrust is insufficient, the speed is decreased, and the work is unstable
(1) Internal leakage of hydraulic cylinder. Internal leakage of hydraulic cylinder includes leakage caused by excessive wear of hydraulic cylinder seal, piston rod and seal cover seal and piston seal.
The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.
The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and cylinder, and the phenomenon of "pulling the cylinder" appears. The treatment method is to adjust the speed control valve, according to the installation instructions should do the necessary operation and improvement; Clean the filter or replace the filter element and hydraulic oil.
(2) Hydraulic circuit leakage. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve.
(3) The hydraulic oil passes back to the oil tank through the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the oil tank through the relief valve bypass, resulting in no oil in the hydraulic cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the hydraulic cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.
3. Piston slip or crawl
Hydraulic cylinder piston slip or crawl will make the hydraulic cylinder work unstable. The main reasons are as follows:
(1) Internal astringency of hydraulic cylinder. The internal parts of the hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the speed of the hydraulic cylinder piston changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.
(2) poor lubrication or poor hydraulic cylinder bore processing. Because the piston and cylinder, guide rail and piston rod are relative movement, if poor lubrication or hydraulic cylinder bore is out of alignment, it will aggravate wear, reducing the straightness of the cylinder center line. In this way, when the piston works in the hydraulic cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the hydraulic cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.
(3) Hydraulic pump or hydraulic cylinder into the air. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke.
(4) Seal quality is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and lip elongation, but also easy to cause slip or crawling, in order to prevent its tip can be used to maintain its stability.
4. Adverse consequences of scratches on the surface of the inner hole of the hydraulic cylinder body and quick repair methods:
① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working part of the seal during operation.
② Deterioration of the surface roughness of the inner wall of the cylinder, increase friction, easy to produce crawling phenomenon.
③ Increase the internal leakage of the hydraulic cylinder, so that the working efficiency of the hydraulic cylinder is reduced. The main causes of scratches on the surface of the inner hole of the cylinder body are as follows:
(1) Scars caused by assembling hydraulic cylinders
Before the hydraulic cylinder is assembled, all parts must be fully removed burrs and cleaned. When the parts are installed with burrs or dirt, foreign bodies are easily embedded into the surface of the cylinder wall due to "other strength" and the weight of the parts, causing scars.
When the hydraulic cylinder is installed, the piston and the cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how it will not be strong, therefore, the end of the piston or the cylinder head boss in the inner surface of the cylinder wall, it is easy to cause scars. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized hydraulic cylinders, only meticulous and careful operation can be avoided.
③ The scars caused by the measuring instrument contacts are usually used to measure the inner diameter of the cylinder body when the measuring contacts are inserted into the inner hole wall of the cylinder body by friction, and the measuring contacts are mostly made of high hardness wear-resistant cemented carbide. Generally speaking, the slender scratch caused by the small depth of the measurement is slight and does not affect the operating accuracy, but if the measurement rod head size is improperly adjusted, the measurement contact is hard and embedded, it will cause more severe scars. The solution to this problem is first to measure the length of the adjusted measuring head, in addition, with a paper tape only in the measuring position of the hole, affixed to the inner surface of the cylinder wall, that is, no scratches of the above shape. Slight scratches caused by measurement can generally be erased with the back of the old emery cloth or horse manure paper.
(2) No serious running wear marks
① Scars on the sliding surface of the piston Before the piston is installed, there are scars on the sliding surface of the piston, which are not treated and are installed intact, and these scars will in turn scratch the inner surface of the cylinder wall. Therefore, before installation, these scars must be fully repaired.
② The sintering phenomenon caused by excessive pressure on the sliding surface of the piston is caused by the piston rod's self-weight, which tilts the piston and causes the phenomenon of stiffness, or the pressure on the sliding surface of the piston rises due to the effect of transverse load, which will cause the sintering phenomenon. In the hydraulic cylinder design must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.
③ The hard chrome layer on the inner surface of the cylinder body is stripped off. It is generally believed that the reasons for the peeling of the electroplated hard chrome layer are as follows:
a. coating bonding is not good. The main reasons for poor bonding of electroplating layer are: before electroplating, the degreasing treatment of parts is not enough; The surface activation treatment of the parts is not complete, and the oxide film layer is not removed.
b. Hard layer wear. The wear of the hard chromium plating layer is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is moisture in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.
c. Corrosion due to contact potential difference. Contact potential difference corrosion is not easy to occur for hydraulic cylinders running for a long time; It is a common fault for hydraulic cylinders that have been stopped for a long time.
④ Damage of the piston ring The piston ring is damaged during operation, and its debris is caught in the sliding part of the piston, causing scratches.
⑤ The material of the sliding part of the piston is sintered and cast, which will cause sintering phenomenon when it is subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.
(3) There are foreign bodies in the cylinder
Among the failures of the hydraulic cylinder, the most problematic is that it is difficult to determine when the foreign body is into the hydraulic cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.






